aboutsummaryrefslogtreecommitdiffstatshomepage
path: root/OpenSim/Region/Physics (follow)
Commit message (Collapse)AuthorAgeFilesLines
...
* Changed application of constant forces to after PID force is applied. ↵Dahlia Trimble2008-07-241-3/+7
| | | | llSetForce() should behave identical to the Linden implementation now.
* Implements llSetForce() and llGetForce(). These are experimental and the ↵Dahlia Trimble2008-07-248-4/+16
| | | | units may not match the Linden implementation.
* Clean up Meshmerizer.cs a bit to make it more readableDahlia Trimble2008-07-211-250/+2
|
* refactor - commenting out needsMeshing() and all references as createMesh() ↵Dahlia Trimble2008-07-182-179/+297
| | | | has the same logic and obsoletes the need for it.
* Passes prim physical status to mesher from physics pluginsDahlia Trimble2008-07-124-19/+21
| | | | | | | Small prims now get a full mesh if they are physical Fixed a logic bug that was preventing many prim meshes from having excess memory cleaned up Switched to more conservative method of vertex and triangle list trimming to prevent possible crash
* Overloads CreateMesh method of interface IMesher to pass prim physical ↵Dahlia Trimble2008-07-124-1/+12
| | | | status to mesher
* Trim out nulls from mesh vertex and triangle lists to try and save more memoryDahlia Trimble2008-07-111-6/+22
|
* Experimental physics optimization: prims with all 3 dimensions less than 0.2 ↵Dahlia Trimble2008-07-111-0/+101
| | | | meters will be meshed as a simple box
* added a hollow size constraint to box, cylinder, and prism prim meshes to ↵Dahlia Trimble2008-07-071-0/+8
| | | | prevent a possible sim lockup
* Addresses more problem box cut anglesDahlia Trimble2008-07-071-6/+4
|
* fix some Meshmerizer problem angles for sphere dimple and box path cutDahlia Trimble2008-07-071-4/+15
|
* disables changes in r5356 until I have more time to do further characterizationDahlia Trimble2008-07-061-2/+2
|
* Corrects errors in sphere mesh with dimple start angle > 0 and hollow == 0Dahlia Trimble2008-07-061-2/+2
|
* alters a problem path cut angle for the cylinder prim profileDahlia Trimble2008-07-061-0/+9
|
* Adds experimental Meshmerizer support for "prim torture" effects of sphere ↵Dahlia Trimble2008-07-022-5/+21
| | | | dimple on prim types box, cylinder, and prism
* properly explaining each #pragma warning disableDr Scofield2008-06-302-4/+6
| | | | | | massaging OSHttpRequestPump to not abort on exceptions...
* disables spam-like debugging messages inadvertently left on in last commit ↵Dahlia Trimble2008-06-301-1/+1
| | | | (oops)
* Corrects Meshmerizer orientation of profile cut angles for ring type primDahlia Trimble2008-06-301-2/+9
|
* Corrects meshmerizer profile cut angle orientation for tube type primsDahlia Trimble2008-06-301-0/+7
|
* Altered prim description/debugging message code to be more warning friendlyDahlia Trimble2008-06-281-33/+33
|
* Mantis#1620. Applied Melanie's patchCharles Krinke2008-06-281-32/+33
|
* altered prior warning fix to Meshmerizer.cs to allow mesh debugging code to ↵Dahlia Trimble2008-06-281-31/+32
| | | | function
* last round of warning squashing. calling it a day now.Dr Scofield2008-06-271-1/+5
|
* dr scofield's warnings safari:Dr Scofield2008-06-278-82/+89
| | | | | | * commenting out unused variables
* Minor refactoring of POS. Adds a Util.Clamp(x, min, max) function.Jeff Ames2008-06-261-52/+19
|
* Separate POS classes into mutiple files.Jeff Ames2008-06-264-715/+822
|
* Minor formatting cleanup.Jeff Ames2008-06-252-20/+24
|
* More svn properties. Minor cleanup in POS.Jeff Ames2008-06-251-32/+47
|
* Modifies box prim profile cut parameters to avoid angles which cause ↵Dahlia Trimble2008-06-251-0/+11
| | | | spurious triangles in mesh
* Changes selection criteria to allow meshing of more sphere prim configurations.Dahlia Trimble2008-06-212-2/+18
| | | | | Adds comments to some functions in Meshmerizer.cs.
* * Patch from nlin to enable DIF state file writing from the ODEPluginTeravus Ovares2008-06-201-0/+28
| | | | | | * Rebuilt libode.so, ode.dll * If you roll your own ODE library, make sure to update your opensim-libs.
* * Patch from Dahlia - 0001576: Exception of type ↵Teravus Ovares2008-06-191-0/+4
| | | | | | | 'System.OutOfMemoryException' was thrown .Void set_Capacity(Int32), with regards to sphere mesh. Thanks Dahlia! * Also allows a sphere to be hollow with no cuts or dimples. (walking around inside the sphere).
* * 0001571: (PATCH) patch to implement editable sphere meshes for ↵Teravus Ovares2008-06-191-17/+111
| | | | | | | meshmerizer/ode (Initial Implementation) from Dahlia! Thanks Dahlia!!! * The included patch implements the editor parameters twist, dimple, path cut, and profile cut to the sphere mesh for meshmerizer. The mesh will default back to the geodesic sphere if the parameters are adjusted to beyond a reasonable arbitrarily chosen threshold that would expose too many inverted normals on the mesh.
* * 0001558: [PATCH] Add support for full collision geometry feature set for ↵Teravus Ovares2008-06-152-88/+296
| | | | | | | linear path prims (patch attached) By Dahlia. Thanks Dahlia! * This update re-does the cube/cylinder/prism prims to dynamically add faces as twist is used.
* Update svn properties. Formatting cleanup.Jeff Ames2008-06-101-10/+10
|
* *Fixed bug that caused failure when System.Console.Readline returns null (no ↵mingchen2008-06-091-4/+10
| | | | | | | stdin) *Fixed bug that would crash the simulator if there were two physics/meshing engines loaded with the same name.
* * Added a check for a non-finite heightfield array value passed to the ↵Teravus Ovares2008-06-041-0/+9
| | | | ODEPlugin. This may, or may not fix anything.
* * From DahliaTeravus Ovares2008-06-041-21/+36
| | | | | | | * Committing : 0001449: Patch implements X and Y Top Shear parameters for torus prim physical mesh generation (PATCH attached) * The included patch implements the X and Y Top Shear parameter adjustments to the mesh generator for the torus prim physical mesh. These are approximations as I was unable to determine their exact function but they appear to generate meshes which quite closely duplicate their counterparts in the viewer. * Thanks Dahlia!!!!
* Formatting cleanup, minor refactoring, svn properties.Jeff Ames2008-06-041-10/+17
|
* PATCH : 0001431: corrections to torus physical mesh for default hollow shape ↵Teravus Ovares2008-06-022-19/+38
| | | | | | | | and taper orientation along path. --------- From Dahlia! Thanks Dahlia!!! the attached patch reinstates the default hollow shape of the physics mesh of the torus prim type and corrects the orientation of the effects of taper on the profile along the path.
* * While I couldn't reproduce it, I was able to see how it *might* happen, so ↵Teravus Ovares2008-06-021-2/+5
| | | | therefore; fix to: 0001058: Physics crash when changing Type of Prim intersecting with ground.
* * Applying Dahlia's patch : 0001429: Patch to fix prism physical mesh and ↵Teravus Ovares2008-06-012-60/+132
| | | | | | | add path start and end to skew z offset of circular path prim meshes (PATCH attached) * Apparently this fixed a bug in my code that caused PushX to appear to work and pushX didn't appear to work after the patch.. so I fixed that after applying this patch and PushX actually works now.
* Update svn properties. Formatting cleanup.Jeff Ames2008-05-302-25/+10
|
* * Fixes a few taper/top-sheer situations that were previously having issues.Teravus Ovares2008-05-291-2/+2
|
* * Applying Dahlia's interim path curve patch. it adds initial support for ↵Teravus Ovares2008-05-294-47/+669
| | | | | | | | | some tori/ring parameters. Thanks Dahlia! * Some situations do not match the client's render of the tori, we know and are working on it. This is an initial support patch, so expect it to not be exact. * Some tapers are acting slightly odd. Will fix.
* * Adds Top Colliders when using ODE. Access it from the estate tools/debug tab.Teravus Ovares2008-05-259-3/+76
|
* * Yet another way to optimize the sculpt mesh generatorTeravus Ovares2008-05-251-25/+25
|
* * kill a potentially large float array.Teravus Ovares2008-05-251-1/+1
|
* * Releases Pinned vertex/index list in ODE on next mesh request.Teravus Ovares2008-05-253-5/+28
|
* * Prevent an error from stopping startup when decoding the sculpt mesh j2k ↵Teravus Ovares2008-05-221-2/+12
| | | | fails.
generated by cgit v1.1 at 2024-11-01 21:36:05 +0000